
Generation 4 CommandCenter Software Update 2017-2
StarFire 6000 Software Update 2017-2
The GreenStar Live Update is a desktop software application that will help you make sure your GreenStar (GS) display always has the latest software from John Deere ISG. To install GS Live Update, click on the link below, and follow the on-screen prompts. Once installed, it will alert you when new GreenStar software updates are available, and walk you through the downloading process.
Please follow the steps below:
Release Date: 03/2017
Version:
Important Notes:
To ensure that your GS display will update successfully, please verify that your display currently has the following software version installed:
If the software version is a smaller number, please contact your dealer. To determine the currently installed software version, select Menu » Display » Diagnostics » About and reference the Application Software Build number.
Before starting the update, please unplug ALL implements from the ISOBUS- (or implement-) connector at the back of the tractor.
The only implements currently updated via GS LiveUpdate are:
If you need to update one of the above listed implements/controllers, leave it connected to the ISOBUS socket.
N-Sensing activation procedure:
For a N-Sensing activation please contact your local John Deere dealer.
This update allows the StarFire 3000 receiver and other controllers to be updated with the latest software using the GreenStar 3 CommandCenter display.
This is a controller-only update. Please see the Release Notes document for a list of available controller software versions.
When a display update is available, it will require your John Deere dealer to update the display.
Instructions to download: Download all of the files to a USB stick, then insert the USB into the USB connector located in the armrest storage compartment to update the controllers.
Release Date: 03/2017
This update allows the Generation 4 CommandCenter to be updated with the latest software version.
Important Note: When installing this software version, it may spend up to 90 minutes at the same percentage level (such as 82%) in the Installing Software stage. Please be patient.
Software Manager
Download
In order to save time with this large download, use the same USB or C:\ drive each time.
Software Manager Utility Instructions
Download & Update Instructions
Release Notes 2017-2
Version: 10.9.79-111
Release Date: 08/2017
Software Manager for Mac OS
Release Date: August 2017
StarFire ™ 6000 Update: 3.70M
Active implement Guidance and iGrade application controller 1100 starting with version 2.00 software, will require a download to support the following languages:
Release Date: 02/2017
Download Instructions:
NOTE: Language files on the USB memory stick are needed every time the language is changed.
Field Connect Firmware Version 1.11.75 (March 2016)
Download File 1 (MPFILE.BIN)
Download File 2 (GWFRMWR.BIN)
NOTE: Update has two files (GWFRMWR.BIN and MPFILE.BIN) that must be loaded. Do not change file name.
Release Notes / Firmware Installation Instructions
For HarvestLab Software Updates please contact your local dealer.
ORIGINAL GREENSTAR SYSTEM UPDATE
This product enhancement is for all Original GreenStar Systems. Download this Update onto your computer. The update wizard will install the needed software to your John Deere KeyCard.
StarFire 3000 not in Region 2 Original GreenStar image for Software Updates (SU) 2011-1
Due to space limitations on the keycard and additional Region 2 controllers, the SF3000 software file is not included in the Region 2 (Europe) Original GreenStar update image for SU2011-1.
Note: This update requires a 32MB Key Card.
Version: 1.97 B
February 2011
Release Notes
Instruction Guides for Original GreenStar System
These instructions will help you step by step download the latest software from the website, to the computer, to the card, then to the system.
PRINTER SOFTWARE FOR YIELD MONITORING
Printer Software for Original GreenStar System
Printer software is available for your combine Yield Monitoring system (only in combination with Mobile Processor). Download the wizard and run it on your John Deere KeyCard or Datacard. Finally, use your KeyCard or DataCard to reprogram your mobile processor. The KeyCard or DataCard has to remain in the mobile processor while operating the printer.
Note: If you are using a printer with any other GreenStar application do NOT use the printer software, but reprogram your mobile processor with the corresponding software available with the GreenStar System Update. The printer software is included in these software files.
Software on Mobile Processor | ||
---|---|---|
System | Combine | SPFH |
Printer & Yield Monitoring | Printer software | -- |
Printer & Yield Mapping | Yield Mapping software | -- |
Printer & Harvest Monitor | AutoTrac & Parallel Tracking software | AutoTrac & Parallel Tracking software |
Printer & Harvest Doc | Harvest Doc Combine software | Harvest Doc SPFH software |
DATACARD GENERIC SETUP FOR ORIGINAL GREENSTAR SYSTEM
The GreenStar Standard Setup on the DATACARD for Field Doc or Harvest Doc can ONLY be used for boundary measurement, if there is no other desktop software available to generate the setup information (see also Field Doc operators manual). Please NOTE that this Standard Setup is NOT compatible with any desktop software program. This means that the data (boundary information) collected with this Standard Setup file cannot be downloaded into any type of desktop software application at a later date!
Software on Mobile Processor | ||
---|---|---|
System | Combine | SPFH |
Printer & Yield Monitoring | Printer software | -- |
Printer & Yield Mapping | Yield Mapping software | -- |
Printer & Harvest Monitor | AutoTrac & Parallel Tracking software | AutoTrac & Parallel Tracking software |
Printer & Harvest Doc | Harvest Doc Combine software | Harvest Doc SPFH software |
ISOBUS Sprayers (800i/700i/M700(i)/M900(i)/R900i) - Loadable Languages
NOTE: To run the new software for ISOBUS (i-machines) sprayers in different languages than English it's also necessary to upload new language files to the sprayer as described below.
Loadable Language Revision Overview MY16
Software ISOBUS Sprayers (800i, 700i, M700(i), M900(i) and R900i)
Revision Date: 01/04/2016
700i - 900i | M700(i)/M900(i)/R900i | |||
Compatible software | 4.11 & 4.12 | 5.20 & 6.07 | ||
Language | Version | Release Date | Version | Release Date |
Bulgarian (bg) | -- | -- | 39.04 | 01/04/16 |
Czech (cz) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Danish (da) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
German (de) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
English (en) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Spanish (es) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Estonian (et) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
French (fr) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Croatian (hr) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Hungarian (hu) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Lithuanian (lt) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Latvian (lg) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Dutch (nl) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Polish (pl) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Swedish (sw) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Finnish (fi) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Slovak (sk) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Serbian (sr) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Russian (ru) | 09.07 | 15/01/10 | 39.04 | 01/04/16 |
Portuguese (pt) | -- | -- | 39.04 | 01/04/16 |
Norwegian (no) | -- | -- | 39.04 | 01/04/16 |
Romanian (ro) | -- | -- | 39.04 | 01/04/16 |
Sprayers with Original GreenStar Display (GSD4)
It is not recommended to reprogram the sprayer controller with the latest software update unless specifically required! Usually the EHC-2 switchbox already has the latest software installed (see notes below).
NOTE:
The sprayer software available for downloaded is only for machines with the 1 MB CPU number WZ8814071. This CPU is used since machine number WZ0****003654, and replacing the earlier 64 kB CPU WZ8814051, that had not enough memory for running BoomTrac, FieldDoc and the TwinFluid low drift settings. In some cases WZ8814071 was retrofitted on earlier sprayers (with software version 1.18).
If the downloaded software is installed it will show a new symbol in your startup menu. Be sure to have the Keycard in the computer before clicking this icon. The new software will automatically be installed on the Keycard.
ATTENTION:
If you want to reprogram with this Keycard the JD Horst Sprayer you must always download the sprayer software (as last step) from Stellar Support after other AMS software has been downloaded to the keycard. If this is not done, it will not be possible to reprogram the sprayer controller on the JD Horst Sprayer.
Please verify what software you need before downloading:
Round Baler ISOBUS RB644 and Wrapping Baler ISOBUS WB678 - WB744 – Loadable Languages
NOTE: To run the new software in languages other than English it is also necessary to load new languages files, as described below.
Round Baler ISOBUS 864, 960 and 990 – Loadable Languages
NOTE: To run the new software in languages other than English it is also necessary to load new languages files, as described below.
The Generation 4 Command Center OnScreen Help is a supplement to the Operator’s manual. The OnScreen Help can be displayed on a Smartphone. The same help file can also be found in the Generation 4 Command Center.
The AB line merge tool is designed to manipulate Straight or Circle Track lines from the Original GreenStar System. It will allow you to reorganize the AB lines on your card, merge multiple cards' AB line information as well as Copy one card's AB lines to other cards. This tool is for the Original GreenStar System only, it is not compatible with GS2 AB lines.